HONGYANG GROUP Honduras Technical Center

Fax: +86 (577)88097280

HONGYANG Group logo

HONGYANG GROUP Honduras Technical Center , Discuss Technical Problem , Suply After Service Online of Fuel Dispenser, Please Regist Firstly

P-GQ FUEL DISPENSER

P-GQ

P-GQ FUEL DISPENSER

FlowMeter Type :Optional

Accuracy :±0.2%

Pressure Loss (kg/cm):Under 0.25

Motor Voltage(V): 110V/220V/380V,50Hz/60Hz

Capacity(hp) :1HP(0.75kw)

Input Voltage : 110V/220V/380V,50Hz/60Hz

Nozzle : Auto Shut-off Nozzle

Environmental Condition : -40~~+55degree

Control Type : Solenold Vale Control Type

Preset : Function Provided(Small LCDIndicator)

Display(Counter):Type LCD and Bright Backlight

Digit of Volume :0~~999,999(6 Digits),Decimal point can be changed

Digit of Amount :0~~999,999(6 Digits),Decimal point can be changed

Digit of Unit price : 0~~9999(4 Digits),Decimal point can be changed

Digit of Total Range :0~~99,999,999,99

Optional Display :Type LCD and Bright Backlight

Digit of Volume : 0~~99,999,999(8 Digits),Decimal point can be changed

Digit of Amount : 0~~99,999,999(8 Digits),Decimal point can be changed

Digit of Unit price : 0~~999999(6 Digits),Decimal point can be changed

Digit of Total Range: 0~~99,999,999,99

Totalizer: 1~~9,999,999

Hose :4.5m

Weight :205kg

Dimension(L×W×H) : 1060*550*1620(mm)

Dimension(L×W×H)Of Qty of Container : 40ft: 44 20ft: 22

products links

links

technical archives

    ws into pipe because of adapting one pipe in two fuel dispensers or other leakage. Bottom valve in tank or single valve in pipeline is stuck and damaged, no oil into pump. Oil level is lower than bottom valve or suction nadir. Counter at beginning of operation Due to long and much soft, hose tends to bulge under a certain pressure. Transducer will count as bulging pressure out of certain scope. This trouble can’t be solved through shorten or replace hose. As leakage in bottom valve or pipe, oil flow back into tank between operation interval because of lower oil level in vapor separator and pump. Air in transducer drives to count as next time refueling. The longer interval time the more data jump. Inspect and solve pipeline leakage of oil and air. Unstable flow rate makes large tolerance; air leakage in bottom valve and pipe oil level low than bottom valve bring about much air flow into fuel dispenser. Article III Important notices to dispenser’s maintenance Due to fuel dispenser located in flammable and combustible location, operator should pay much attentions to security preventing accident occur on human and equipment, and strictly abide by the following general requirements: Smoking and open flame is strictly prohibited in filling station in case lead to fire. Maintainer should, in accordance with safety regulations in filing station, not wear shoes with metal nail and chemical fiber easy to generate static. Cut power supply prior to maintain fuel dispenser; pick down V belt then empty oil filled in part where need to be done. Pour oil into container in case of splash out. Repairing tools should be explosion-proof, prohibiting randomly throw in case of generating spark and accident. Pay much attention not to the joint surfaces of seal and metal parts, which would lead to leakage. All components and sections should be cleaned so to prevent giblets or waste destroying parts. fuel dispenser Carefully inspect wire connection after maintaining electric equipment, abstaining new trouble. fuel dispenser fuel dispenser

technical specification

    When tested according to 6.1.7.2 there shall be no catastrophic failure such as rupture.   NOTE Steel pipe according to ISO 9329-1 to -4 and copper pipe according to EN 1057 of the appropriate material grade   and section are suitable materials to meet the criteria according to 6.1.7 of this standard.   In order to prevent discharges between nozzle and filler necks of receptacles that could cause ignition   5.3.3.4   materials and components shall be selected to ensure that the resistance between nozzle spout and earth is less   than 10 ?. For test see Table 3.   6   Piping pipe fittings and components through which liquid fuel or vapour flows shall be constructed of   5.3.3.5   materials which do not directly contribute to the development of a fire.   The test shall be carried out according to EN ISO 1182.   Piping pipe fittings and components through which liquid fuel or vapour flows shall be constructed from materials   which shall not be degraded by the external environment in which the material is used. The parts shall be of   corrosion resistant material or be provided with a corrosion resistant protective coating.   Conformity shall be demonstrated by supplier s declaration which shall specify the materials used.   Materials shall be selected such that electrolytic corrosion is prevented this may be achieved by   5.3.3.6   coatings on materials.   Conformity shall be demonstrated by supplier s declaration which shall specify the materials used.   fuel dispenser fuel dispenser fuel dispenser

we are committed to create the best workplace, encourage our staffs to put their own personalities into their jobs, and provide them a stage to show themselves.

    Caveat investor The Supreme Court Business Education The brainbox and the blowhards Executive Dialogue The corporate-pension shift Join the queue School choice FINANCE & ECONOMICS Why judges matter American banks and property Economics Focus Sleeping in the vault No DeLay Economics A-Z Time for a proper fight SCIENCE & TECHNOLOGY Stockmarket indices The Dow puffs on A spending splurge in California Technology Quarterly Build it Credit cards PEOPLE Making advances Tax policy Tripe is back on the menu Obituary Relative economic performance fuel dispenser Les miséra fuel dispenser fuel dispenser